Tree Trimming Near Me

Tree Arborist Near Me

Tree Trimming Near Me

Tree trimming, also known as pruning, is the process of removing dead, diseased, or overgrown branches from a tree in order to promote healthy growth and maintain its shape. This process is important for a variety of reasons including safety, aesthetic appeal, and the overall health of the tree. One of the most important reasons for tree trimming is safety. Dead or diseased branches can easily fall and cause damage to property or injury to people. Additionally, overgrown branches can grow into power lines, causing power outages or even starting fires. By removing these potentially dangerous branches, tree trimming can help prevent accidents and protect both people and property.

One important reason for tree trimming is aesthetic appeal. Trees that are overgrown or have unshapely branches can detract from the beauty of a yard or landscape. By removing these branches, the tree’s natural shape and beauty can be restored, making it an attractive addition to any landscape.

Tree trimming is also important for the overall health of the tree. By removing dead or diseased branches, the tree can focus its energy on healthy growth. Additionally, trimming back overgrown branches allows light and air to penetrate the tree’s canopy, which can help prevent the growth of mold and mildew. This can also help reduce the risk of pests and diseases that thrive in dark, damp environments. There are several different techniques that can be used when trimming a tree, depending on the size and type of tree, as well as the specific purpose of the trimming. The three main types of tree trimming are crown cleaning, crown thinning, and crown reduction.

Crown cleaning involves removing dead, diseased, or broken branches from the tree’s canopy. This helps to promote healthy growth and prevent the spread of disease. Crown thinning is similar to crown cleaning, but instead of removing branches, it involves removing a small portion of the tree’s canopy in order to allow more light and air to penetrate the tree. This can help to reduce the risk of pests and diseases, and promote healthy growth.

Crown reduction is the most drastic type of tree trimming. It involves removing a large portion of the tree’s canopy in order to reduce the overall size of the tree. This is typically done when a tree has grown too large for its location, or if it is causing damage to nearby structures. It is important to note that tree trimming should always be performed by a professional arborist. A professional arborist has the knowledge and equipment necessary to safely trim a tree, and can ensure that the tree is trimmed in a way that promotes healthy growth and prevents future problems.

Tree trimming is not only important for safety and aesthetic reasons, but also for the overall health of the tree. Regular tree trimming can help to prevent the spread of disease, reduce the risk of pests, and promote healthy growth. By working with a professional arborist, you can ensure that your tree is trimmed in a way that promotes its long-term health and beauty.

However, there are also some considerations and precautions to take when trimming trees, as improper pruning can cause more harm than good. For example, it is important to avoid removing more than 25% of a tree’s canopy in a single year, as this can shock the tree and cause it to become weak. Additionally, it is important to avoid topping a tree (removing the top of the tree) as this can cause the tree to become unstable, and can also cause an increase in the growth of water sprouts (shoots that grow from the base of the cut) which are weakly attached and are more prone to breaking.

When providing a proposal for a tree removal, an arborists also evaluate the site for stump grinding. While having the stump ground is not always necessary, many people prefer to deal with the stump at the same time as having the tree removed. Stump grinding allows the property owner to use the area where the tree once stood for laying sod or planting a flower bed. The stump grinder also produces mulch that has many uses around the yard. Here are answers to some common questions we get about stump grinding. Tree trimming is the process of removing dead, diseased, or overgrown branches from a tree to maintain its health and appearance. It is an important aspect of tree care, as it can help prevent damage to property and people, and can also improve the tree’s overall health and appearance.

There are several reasons why tree trimming is necessary. First, dead or diseased branches can pose a danger to people and property if they fall. Second, overgrown branches can interfere with power lines, sidewalks, and other structures. Third, trimming can help to promote the tree’s overall health by allowing sunlight and air to reach the inner parts of the tree, which can improve its growth and fruit production.

When it comes to trimming a tree, there are a few things to keep in mind. First, it is important to only remove branches that are dead, diseased, or overgrown. Removing healthy branches can harm the tree and can also lead to an unbalanced shape. Second, it is important to use the proper tools and techniques to avoid damaging the tree. Third, it is important to trim at the right time of year, as some trees have specific pruning needs and may be sensitive to certain types of trimming at certain times of the year.
One of the most important things to consider when trimming a tree is safety. Always wear protective gear, such as goggles, gloves, and a hard hat, and use a sturdy ladder or lift to reach high branches. It is also a good idea to work with a partner or to hire a professional tree trimming service to ensure that the job is done safely and correctly.

When it comes to the tools needed for tree trimming, there are a few basic items that you will need. A good pair of pruning shears, a chainsaw, and a pruning saw are the most essential tools. You may also need a ladder or lift, as well as a pair of safety goggles and gloves to protect yourself while working.

The first step in tree trimming is to identify the branches that need to be removed. Dead branches should be removed first, as they are the most likely to fall and cause damage. Diseased branches should also be removed, as they can spread their disease to the rest of the tree. Overgrown branches should be removed next, as they can interfere with power lines, sidewalks, and other structures.

Once you have identified the branches that need to be removed, it is time to start trimming. When trimming, it is important to make clean, precise cuts. Use a chainsaw or pruning saw to remove large branches, and use pruning shears for smaller branches. Make sure to cut the branch at a slight angle, so that water will run off of the cut. After the tree has been trimmed, it is important to clean up any debris that has fallen to the ground. This includes leaves, twigs, and branches. It is also a good idea to mulch the debris, as it can be used as a natural fertilizer for the tree.

When a tree becomes too big for a section or is in danger of falling because of disease or age, tree pruning or tree removal may be your only option. As tree pruning and arboriculture experts, the tree trimming crews mostly have everything you need to get the job done and offer both a one off service or ongoing maintenance programs, as required. Whether your objective is to promote tree growth or better fruit production, or to improve your view and let more sunlight in, our tree trimming crews are qualified and experienced to do the job. Pruning a tree in a confined residential section can require a great deal of skill. Key considerations need to be given to avoid damage to surrounding buildings, water pipes, power lines and existing vegetation. The experienced arborists have the equipment and the techniques to perform tree pruning services with minimal fuss and with safety in mind. All staff are trained, and completely up to date with modern arboricultural practices, with work carried out to AS 4373-2007 standard for pruning of amenity trees.

In conclusion, tree trimming is an essential part of tree care that can help maintain the tree’s health and appearance, and also prevent damage to property and people. It is important to use the proper tools and techniques, and to trim at the right time of year. Safety should always be a top priority when trimming a tree. With the proper knowledge and tools, you can keep your trees healthy and beautiful for many years to come. You must keep your trees and vegetation clear of the growth limit zone around overhead network power lines. Depending on the type of network line, the trees need to be trimmed when they reach a certain proximity to the line.

[geocentric_weather id="8bf5ad30-523f-42f7-a061-0ae370224dd4"]

[geocentric_about id="8bf5ad30-523f-42f7-a061-0ae370224dd4"]

[geocentric_neighborhoods id="8bf5ad30-523f-42f7-a061-0ae370224dd4"]

[geocentric_thingstodo id="8bf5ad30-523f-42f7-a061-0ae370224dd4"]

[geocentric_busstops id="8bf5ad30-523f-42f7-a061-0ae370224dd4"]

[geocentric_mapembed id="8bf5ad30-523f-42f7-a061-0ae370224dd4"]

[geocentric_drivingdirections id="8bf5ad30-523f-42f7-a061-0ae370224dd4"]

[geocentric_reviews id="8bf5ad30-523f-42f7-a061-0ae370224dd4"]

Tree Removal Near Me Salt Lake City Utah

Tree Removal Grantsville Utah

Tree Removal Near Me

Trees that grow too high may stretch towards electrical cables and cause problems. Tree branches can also obstruct views. In short, tree removal is needed when these situations occur. Homeowners may be compelled to take away trees to make way for a particular construction project. You have the option to cut down unwanted trees provided you have the expertise and equipment. Otherwise, get the services of professional tree removal services. These companies will give the service you like for a minimal cost.

The process of cutting trees is a complicated task. It has to be carried out by professionals who can cut down trees without destroying any structures. The task is more dangerous if the trees stand near electrical posts and wires. Trees located near edifices and fences are not easy to remove while those located in open spaces are easier to remove. Costs depend on the tallness, thickness, form and quantity of branches.

What should you do?

You should inspect every tree that is likely to have problems. To prevent accidents, you have to do these inspections periodic and thorough. At least once a year, but we recommend two (summer and winter).

Treatments

To keep the tree in the landscape, on rare occasions, you can do pruning, cabling and bracing. But most often tree removal is the only solution to a hazardous tree.

Prevention

Prevention is the best action, you should start a health program as soon as possible. If you want to prevent many problems in the future, always do a proper choice and placement of the trees. Homeowners often create hazards when they buy and plant a tree with no planning.

During construction take special care of your trees. Be attentive when installing a driveway and digging utility lines. Do not let the construction equipment scrape the bark from the trees. Signs of construction stress on trees show up either immediately or years ahead.

Why Would You Need Tree Removal Services

Trees have always provided humans with countless benefits. First, trees are magnanimous beings. It provides beautification. It offers shelter and shade. It even protects us from strong rains. What is even better about trees is that it gives out oxygen after filtering in the poisonous and deadly carbon dioxide. But sometimes trees can do more harm than good. When this unfortunate situation arises, there is nothing else to do but hire tree removal services immediately and let them handle the dangerous cutting and trimming of trees.

Why is it Essential to Remove Trees?

When a tree has taken its toll and is left uncared for, it usually rots on its own. When this happens, it can pose more danger than good in any property or community. Just imagine this scenario: Your children and their friends are playing under a big pine tree located at the community park. Suddenly, you heard a gush and saw that a big branch of the pine tree fell to the ground. Your kids are nowhere in sight. What do you think happened to them? Good thing this is only make believe.

Yes, it is life threatening. The once beautiful pine tree is now a danger to society. So before your kids and their friends suffer terrible injuries or worse, die because of the rotting tree, you need to call tree removal services experts.

Saving the Trees

Other than rotting trees, preventive maintenance is a better way to preserve these God given beings. Sometimes cutting off branches will make its existence longer and make the tree healthier. With well maintained trees, it is safer to be in the same vicinity with. If it is not too late, these wonderful trees can be nursed. Only tree services companies know what to do and you need to inform them. Ask for appropriate tree programs to save the trees in your community.

Tree removal refers to the process of cutting down and removing a tree from a specific location. This can be done for a variety of reasons, such as to clear land for development, to remove a dead or diseased tree, or to improve the overall health of a forest. The process typically involves cutting down the tree using specialized equipment and then removing the stump and debris from the area. Tree removal can be dangerous and should only be done by trained professionals.

Tree removal, also known as tree cutting, is the process of cutting down and removing a tree from a specific location. This can be done for a variety of reasons, such as to clear land for development, to remove a dead or diseased tree, or to improve the overall health of a forest.

The process typically begins with an assessment of the tree, including factors such as its size, location, and condition. Based on this assessment, a plan is created for how the tree will be removed. The tree is then cut down using specialized equipment such as chainsaws, felling wedges, and tree-climbing gear. The tree cutter will carefully cut the tree in a way that will minimize damage to surrounding property and minimize the risk of injury to themselves and others.

After the tree is cut down, the stump is typically removed using a stump grinder. This is a machine that grinds the stump into small pieces, allowing for easy removal and disposal. The debris from the tree, including branches and leaves, is also removed from the area.
Tree removal can be dangerous and should only be done by trained professionals. Tree cutting requires knowledge of tree biology, safety and proper use of equipment and knowledge of local laws and regulations. Improper tree removal can lead to damage to property and injury to people.

Additionally, tree removal can have a significant impact on the environment and it is important to consider the ecological effects of removing a tree. For example, removing a mature tree can have a negative impact on local wildlife, and removing a tree with a large canopy can affect the microclimate of the area.

Therefore, it is important to consider the reasons for removing a tree and weigh the potential benefits and drawbacks before proceeding with the removal. In some cases, it may be more appropriate to preserve the tree or consider other options such as pruning or cabling.
Tree removal can be a complex process that requires careful consideration of several factors, including the health and condition of the tree, its location, and any potential hazards or risks it may pose. In some cases, a tree may need to be removed due to disease or damage, while in other cases it may simply be in the way of construction or other development.

Before removing a tree, it is important to consult with a certified arborist who can assess the tree’s condition and determine whether or not it is safe to remove. If the tree is determined to be a hazard, it may need to be removed as soon as possible. If the tree is healthy, it may be possible to save it through pruning or other means.

When removing a tree, it is important to use proper techniques and equipment to ensure that the tree is taken down safely and without causing damage to surrounding property. This may include using a crane or other specialized equipment to remove the tree in sections, or using a tree spade to dig up the tree and transplant it elsewhere.

After the tree is removed, it is important to properly dispose of the debris, which may include chipping or mulching the wood, or taking it to a landfill. Additionally, it is important to consider what will be planted in place of the removed tree, as well as the overall impact on the surrounding ecosystem.

Overall, tree removal is a serious decision that should not be taken lightly. It is important to consult with professionals, consider the potential risks and benefits, and have a plan in place for removing the tree safely and responsibly.

Expert cutters know how to take care of cutting timber. These service providers do not simply cut a tree without a plan. Measurements have to be taken at the start so that the falling log does not hit any person, house, vehicle or electric post and wires. Trees should be cut at the correct angle so it goes down on the proper direction.

Stump removal is also difficult. It calls for the work of experts to avoid damages. Tree cutting services know how to operate complicated gear such as cranes, special ladders and ropes. These people also consider the safety factor and disease control aspects so you can be assured of a complete service even if you have to spend some money.

Picking the Right Professionals

Look for crews with ample experience in years, with valid certifications and proper studies. Check for customer feedbacks and those people who were satisfied by their work. Compare prices between companies on top of the mentioned requisites of these tree removal services companies. Then, pick the right group for your needs.

At times a tree removal service is needed to prevent injuries from broken trees. If you think your home needs a hazardous tree removal service don’t wait until it’s too late. Contact your local tree care professionals today to learn more about tree care and how it affects your home.

[geocentric_weather id=”4134af15-b02c-4fe0-bd45-fb0e6efba429″]

[geocentric_about id=”4134af15-b02c-4fe0-bd45-fb0e6efba429″]

[geocentric_neighborhoods id=”4134af15-b02c-4fe0-bd45-fb0e6efba429″]

[geocentric_thingstodo id=”4134af15-b02c-4fe0-bd45-fb0e6efba429″]

[geocentric_busstops id=”4134af15-b02c-4fe0-bd45-fb0e6efba429″]

[geocentric_mapembed id=”4134af15-b02c-4fe0-bd45-fb0e6efba429″]

[geocentric_drivingdirections id=”4134af15-b02c-4fe0-bd45-fb0e6efba429″]

[geocentric_reviews id=”4134af15-b02c-4fe0-bd45-fb0e6efba429″]

Tree Pruning Near Me

Tree Pruning Near Me

The main reasons for pruning ornamental and shade trees include safety, health, and aesthetics. In addition, pruning can be used to stimulate fruit production and increase the value of timber. Pruning for safety involves removing branches that could fall and cause injury or property damage, trimming branches that interfere with lines of sight on streets or driveways, and removing branches that grow into utility lines. Safety pruning can be largely avoided by carefully choosing species that will not grow beyond the space available to them, and have strength and form characteristics that are suited to the site.

Pruning for health involves removing diseased or insect-infested wood, thinning the crown to increase airflow and reduce some pest problems, and removing crossing and rubbing branches. Pruning can best be used to encourage trees to develop a strong structure and reduce the likelihood of damage during severe weather. Removing broken or damaged limbs encourage wound closure.

Pruning for aesthetics involves enhancing the natural form and character of trees or stimulating flower production. Pruning for form can be especially important on open grown trees that do very little self-pruning.

All woody plants shed branches in response to shading and competition. Branches that do not produce enough carbohydrates from photosynthesis to sustain themselves die and are eventually shed; the resulting wounds are sealed by wound wood (callus). Branches that are poorly attached may be broken off by wind and accumulation of snow and ice. Branches removed by such natural forces often result in large, ragged wounds that rarely seal. Pruning as a cultural practice can be used to supplement or replace these natural processes and increase the strength and longevity of plants.

Trees have many forms, but the most common types are pyramidal (excurrent) or spherical (decurrent). Trees with pyramidal crowns, e.g., most conifers, have a strong central stem and lateral branches that are more or less horizontal and do not compete with the central stem for dominance. Trees with spherical crowns, e.g., most hardwoods, have many lateral branches that may compete for dominance. To reduce the need for pruning it is best to consider a tree’s natural form. It is very difficult to impose an unnatural form on a tree without a commitment to constant maintenance.

Pollarding and topiary are extreme examples of pruning to create a desired, unnatural effect. Pollarding is the practice of pruning trees annually to remove all new growth. The following year, a profusion of new branches is produced at the ends of the branches. Topiary involves pruning trees and shrubs into geometric or animal shapes. Both pollarding and topiary are specialized applications that involve pruning to change the natural form of trees. As topiary demonstrates, given enough care and attention plants can be pruned into nearly any form. Yet just as proper pruning can enhance the form or character of plants, improper pruning can destroy it.

Pruning Approaches
Producing strong structure should be the emphasis when pruning young trees. As trees mature, the aim of pruning will shift to maintaining tree structure, form, health and appearance.
Proper pruning cuts are made at a node, the point at which one branch or twig attaches to another. In the spring of the year growth begins at buds, and twigs grow until a new node is formed. The length of a branch between nodes is called an internode.
Crown thinning – branches to be removed are shaded in blue; pruning cuts should be made at the red lines. No more than one-fourth of the living branches should be removed at one time.
The most common types of pruning are:
Crown thinning, primarily for hardwoods, is the selective removal of branches to increase light penetration and air movement throughout the crown of a tree. The intent is to maintain or develop a tree’s structure and form. To avoid unnecessary stress and prevent excessive production of epicormic sprouts, no more than one-quarter of the living crown should be removed at a time. If it is necessary to remove more, it should be done over successive years.
Types of branch unions.
Branches with strong U-shaped angles of attachment should be retained. Branches with narrow, V-shaped angles of attachment often form included bark and should be removed. Included bark forms when two branches grow at sharply acute angles to one another, producing a wedge of inward-rolled bark between them. Included bark prevents strong attachment of branches, often causing a crack at the point below where the branches meet. Codominant stems that are approximately the same size and arise from the same position often form included bark. Removing some of the lateral branches from a codominant stem can reduce its growth enough to allow the other stem to become dominant.
Lateral branches should be no more than one half to three-quarters of the diameter of the stem at the point of attachment. Avoid producing “lion’s tails,” tufts of branches and foliage at the ends of branches, caused by removing all inner lateral branches and foliage. Lion’s tails can result in sunscalding, abundant epicormic sprouts, and weak branch structure and breakage.
Crown raising is the practice of removing branches from the bottom of the crown of a tree to provide clearance for pedestrians, vehicles, buildings, lines of site, or to develop a clear stem for timber production. Also, removing lower branches on white pines can prevent blister rust. For street trees the minimum clearance is often specified by municipal ordinance. After pruning, the ratio of the living crown to total tree height should be at least two-thirds.
On young trees “temporary” branches may be retained along the stem to encourage taper and protect trees from vandalism and sun scald. Less vigorous shoots should be selected as temporary branches and should be about 10 to 15 cm apart along the stem. They should be pruned annually to slow their growth and should be removed eventually.
Crown reduction pruning is most often used when a tree has grown too large for its permitted space. This method, sometimes called drop crotch pruning, is preferred to topping because it results in a more natural appearance, increases the time before pruning is needed again, and minimizes stress.
Crown reduction pruning, a method of last resort, often results in large pruning wounds to stems that may lead to decay. This method should never be used on a tree with a pyramidal growth form. A better long term solution is to remove the tree and replace it
Crown reduction – branches to be removed are shaded in blue; pruning cuts should be made where indicated with red lines. To prevent branch dieback, cuts should be made at lateral branches that are at least one-third the diameter of the stem at their union.

Pruning Cuts
Pruning cuts should be made so that only branch tissue is removed and stem tissue is not damaged. At the point where the branch attaches to the stem, branch and stem tissues remain separate, but are contiguous. If only branch tissues are cut when pruning, the stem tissues of the tree will probably not become decayed, and the wound will seal more effectively.
1. Pruning living branches
To find the proper place to cut a branch, look for the branch collar that grows from the stem tissue at the underside of the base of the branch. On the upper surface, there is usually a branch bark ridge that runs (more or less) parallel to the branch angle, along the stem of the tree. A proper pruning cut does not damage either the branch bark ridge or the branch collar.
A proper cut begins just outside the branch bark ridge and angles down away from the stem of the tree, avoiding injury to the branch collar. Make the cut as close as possible to the stem in the branch axil, but outside the branch bark ridge, so that stem tissue is not injured and the wound can seal in the shortest time possible. If the cut is too far from the stem, leaving a branch stub, the branch tissue usually dies and wound wood forms from the stem tissue. Wound closure is delayed because the wound wood must seal over the stub that was left.
The quality of pruning cuts can be evaluated by examining pruning wounds after one growing season. A concentric ring of wound wood will form from proper pruning cuts. Flush cuts made inside the branch bark ridge or branch collar, result in pronounced development of wound wood on the sides of the pruning wounds with very little wound wood forming on the top or bottom. As described above, stub cuts result in the death of the remaining branch and wound wood forms around the base from stem tissues. When pruning small branches with hand pruners, make sure the tools are sharp enough branch collar. This cut will prevent a falling branch from tearing the stem tissue as it pulls away from the tree.
1. The second cut should be outside the first cut, all the way through the branch, leaving a short stub.
2. The stub is then cut just outside the branch bark ridge/branch collar, completing the operation.

2. Pruning dead branches
Prune dead branches in much the same way as live branches. Making the correct cut is usually easy because the branch collar and the branch bark ridge, can be distinguished from the dead branch, because they continue to grow (Fig. 6A). Make the pruning cut just outside of the ring of woundwood tissue that has formed, being careful not to cause unnecessary injury (Fig. 6C). Large dead branches should be supported with one hand or cut with the threestep method, just as live branches. Cutting large living branches with the three step method is more critical because of the greater likelihood of bark ripping.
3. Drop Crotch Cuts
A proper cut begins just above the branch bark ridge and extends through the stem parallel to the branch bark ridge. Usually, the stem being removed is too large to be supported with one hand, so the three cut method should be used.
1. With the first cut, make a notch on the side of the stem away from the branch to be retained, well above the branch crotch.
2. Begin the second cut inside the branch crotch, staying well above the branch bark ridge, and cut through the stem above the notch.
3. Cut the remaining stub just inside the branch bark ridge through the stem parallel to the branch bark ridge.
To prevent the abundant growth of epicormics sprouts on the stem below the cut, or dieback of the stem to a lower lateral branch, make the cut at a lateral branch that is at least one-third of the diameter of the stem at their union.

[geocentric_weather id=”310a1a9d-44fe-4940-9668-cfab35c28531″]

[geocentric_about id=”310a1a9d-44fe-4940-9668-cfab35c28531″]

[geocentric_neighborhoods id=”310a1a9d-44fe-4940-9668-cfab35c28531″]

[geocentric_thingstodo id=”310a1a9d-44fe-4940-9668-cfab35c28531″]

[geocentric_busstops id=”310a1a9d-44fe-4940-9668-cfab35c28531″]

[geocentric_mapembed id=”310a1a9d-44fe-4940-9668-cfab35c28531″]

[geocentric_drivingdirections id=”310a1a9d-44fe-4940-9668-cfab35c28531″]

[geocentric_reviews id=”310a1a9d-44fe-4940-9668-cfab35c28531″]

Tree Cutting Services

Tree Cutting Services

A feller buncher is a type of harvester used in logging. It is a motorized vehicle with an attachment that ca

n rapidly gather and cut a tree before felling it.

Feller is a traditional name for someone who cuts down trees, and bunching is the skidding and assembly of two or more trees. A feller buncher performs both of these harvesting functions and consists of a standard heavy equipment base with a tree-grabbing device furnished with a chain-saw, circular saw or a shear—a pinching device designed to cut small trees off at the base. The machine then places the cut tree on a stack suitable for a skidder, forwarder, or yarder for transport to further processing such as delimbing, bucking, loading, or chipping.

Some wheeled feller bunchers lack an articulated arm, and must drive close to a tree to grasp it.

In cut-to-length logging a harvester performs the tasks of a feller buncher and additionally does delimbing and bucking.

Components and Felling attachment

Feller buncher is either tracked or wheeled and has self-levelling cabin and matches with different felling heads. For steep terrain, tracked feller buncher is being used because it provides high level of traction to the steep slope and also has high level of stability. For flat terrain, wheeled feller buncher is more efficient compared to tracked feller buncher. It is common that levelling cabins are matched with both wheeled and tracked feller buncher for steep terrain as it provides operator comfort and helps keeping the standard of tree felling production. The size and type of trees determine which type of felling heads being used.

Types of felling heads

Disc Saw Head – It can provide a high speed of cutting when the head is pushed against the tree. Then, the clamp arms will hold the tree when the tree is almost completed cutting. It is able to cut and gather multiple trees in the felling head. The disc saw head with good ground speed could provide high production which allows it to keep more than one skidders working continuously.

Shear Blade Head – It is placed against the tree and the clamp arms will hold the tree firmly. Then, the blade will activate and start cutting the tree. Same as disc saw head, it can hold multiple trees before they are placed on the ground.

Chain Saw Head – The floppy head provides minimal control to place the trees on the ground. It might not suit to collect the cut trees or gather the cut stems in the felling head.

Productivity

Comparing other harvesting systems such as chainsaw and harvester, feller buncher has the relatively high productivity among them. The weekly production of the feller buncher was 627 cubic meters of usable logs, while the chainsaw system and harvester system could produce 163 cubic meters and 239 cubic meters respectively. There are several factors affecting the level of productivity of the feller buncher. They include characteristics of stand, terrain conditions, operation location, and the performance of the operator. Many studies indicated that the trees size and the gradient of the slope are the major factors impacting the overall productivity. There was a research suggested that productivity has a significant positive relationship with the tree size which means the larger stem size, larger tree height or larger diameter at breast height (DBH) results in a high productivity of the feller buncher. Terrain conditions such as ground slope and terrain roughness have a significant negative relationship to the productivity of feller buncher which means the steeper of the land or rough terrain condition can bring negative effect to the productivity. One of the studies had found that feller buncher might reduce its productivity when performing operation on a very uneven surface with slopes of more than 20%. However, larger tree size does not necessarily lead to high productivity. The same study compared the operation time when performing clear-cut of the stands with two different average DBH, 24.6 cm and 34.3 cm respectively. Result showed that the productivity when operating the second stand decreased by 32.3% because the time consumption was doubled when larger stands required two-stage of cutting operation.

Cost-effectiveness

The purchase cost of a feller buncher is around $180,000 and its fuel consumption and lubricant consumption is high among other mechanical harvesting equipment. The feller buncher also has the highest hourly cost which is around $99.5 when comparing other equipment such as a harvesters and grapple skidders. Although the total cost of feller buncher is high in overall, the unit production price is the lowest which explains why feller buncher is considered the most cost-effective harvesting equipment. The average unit cost of the feller buncher is $12.1/m3 while the unit cost of the harvesters is $16.5/m3. The unit cost of the feller buncher is primary affected by the tree size and the tree volume. The unit felling cost is lower when the tree size increased. For example, tree with 5 inches at DBH has the unit cost of $70 while tree with 15 inches at DBH has the unit cost of $12. As the cost of feller buncher is high, only large tree volume can produce more profit to cover the high average cost. In terms of stump height, lower stump height can maximise the use of natural resources and prevent wood waste. Mechanical felling such as using feller buncher can prevent 30% of value loss caused by the high stumps.

Maintenance

Feller buncher requires daily maintenance before operation and some components only require periodic maintenance. It could ensure the safety of operators and all the workers around the operation. If damaged or faulty machine is operated, it could result in further damage to the machine which can be more expensive to repair.

Daily or Every 8 hours

Modern style Tigercat feller buncher. Commonly referred to as a tree cutter

Lubrication

The felling head is considered one of the hardest part of the feller buncher and it is necessary to apply lubricant to every joint for daily maintenance. It is suggested to apply lubricant to saw head clamps, wrist attachment and driveshaft bearings during every maintenance. The use of grease should meet the extreme pressure performance standard and contains 3% of molybdenum disulphide (MoS2).

MoS2 can prevent the wear takes place where the metal to metal contact exists.

Fuel

It is also important to check if there is enough fuel for the operation. Feller bunchers use diesel fuel to generate power. In most of the cases, the fuel is preferably to have cetane number greater than 50 (minimum 40). This is suitable when undergo operation for temperature below -20 °C (-4 °F) or elevations more than 1500m (5000 Ft.). The Cloud Point of the fuel is preferably at least 5 °C (9 °F) lower than the expected low temperature. It is also suggested that the sulphur content of the fuel should not be more than 0.5% as it could reduce 50% of the service interval for the engine oil and filter.

Older style felling head that uses a bar and chain to cut trees instead of the more modern saw disk.

Engine coolant

Operators have the responsibility to check the engine coolant level of the feller buncher before starting the engine. The coolant prevents cylinder linear erosion and pitting, and provides protection during extremely low temperature for up to -37 °C (-34 °F). It is recommended to use coolants for heavy-duty engines which are relatively low silicate ethylene glycol base. There are two forms of coolants: pre-diluted or concentrate. Water is required to dilute the concentrated coolant with an approximate ratio of 50:50. The use of supplemental coolant addictive might be also required in the concentrated coolant in order to provide protection against corrosion. Distilled, deionised, or demineralised water is suggested for mixing the concentrated coolant because when some water compositions mix with other substances could form a precipitate, causing damage or blockage in the engine.

Risk management approach

During maintenance, there are common working hazards related to two main areas: working environment and exhaust system. When working on the exhaust system, be aware of the hot components around the engine. Workers could wear personal protective equipment such as safety spectacles, heat-proof gloves and safety boots. When feller buncher is elevated for service or maintenance, falls from height might happen. Related injuries could be avoided by ensuring dryness of all the walking surface, wiping any oils or other liquid substances on the floor. Also, ensure the feller buncher is parked on a level and stable ground during maintenance. When getting in and out of the machinery, workers are suggested to use three point of contact with two hands holding the handrails and one foot on a step. It is also important to provide sufficient lighting for all the working sites at all time of service.

Safety

Logging is considered one of the most dangerous occupations. This is because many loggers are injured by the falling objects which are large in size and heavy. “Struck by object” is the most common injuries that reported in the logging industry due to the manual use of equipment during the logging procedures. There is evidence that using mechanized harvesting equipment could reduce the rate of “struck by” injuries. One study indicates that total injury claims could be reduced by 14.2%, while the “struck by” injuries could be reduced by 8.2%, when comparing the changes before and after the use of feller buncher. The significant decline in the number of “struck by” injuries after using the feller buncher in the logging companies supported the statement that using mechanized harvesting equipment could lessen overall injuries. The evidence also found that the rate of injuries in the logging companies without using feller bunchers had increased slightly throughout a period of time, increasing from 14.5% to 17.5%, in five years. In terms of trees fatality, areas with lower levels of mechanization in harvesting resulted in higher rate of trees fatality. For instance, in Eastern areas of the United States, research which compared the conventional and mechanized logging operations, indicated the number of injuries, when using the conventional approach, is three times greater than that of using the mechanized equipment such as a feller buncher. However, mechanized related injury could be raised accordingly, especially when performing machine maintenance or repair. These kinds of injuries could be serious and also costly.

[geocentric_weather id=”4108152b-ef86-48a4-8627-1083cde7dee1″]

[geocentric_about id=”4108152b-ef86-48a4-8627-1083cde7dee1″]

[geocentric_neighborhoods id=”4108152b-ef86-48a4-8627-1083cde7dee1″]

[geocentric_thingstodo id=”4108152b-ef86-48a4-8627-1083cde7dee1″]

[geocentric_busstops id=”4108152b-ef86-48a4-8627-1083cde7dee1″]

[geocentric_mapembed id=”4108152b-ef86-48a4-8627-1083cde7dee1″]

[geocentric_drivingdirections id=”4108152b-ef86-48a4-8627-1083cde7dee1″]

[geocentric_reviews id=”4108152b-ef86-48a4-8627-1083cde7dee1″]

Stump Removal Near Me

Stump Removal Near Me

Stump Removal Near Me

How to get rid of tree stumps is one of the most frequently asked question in the industry. Once you have had a tree removed you are left with a typically unsightly reminder, the stump. Tree stumps are an eyesore, a tripping hazard, and they can attract unwanted pests like termites or even fungi and bacteria. If left to simply decay and rot away on its own, without any sort of treatment, a stump can take up to ten years to disappear. When it comes to rotting a tree stump in Utah, the rate of decay depends on many different factors such as species of tree, size of the tree, and the climate and weather conditions.

As your leading Utah arborist, we do stump grinding in the Utah and surrounding area, although due to the demand we do have to limit our grinding services and can only offer it to current tree service clients and not as a standalone service.

To remove a tree stump you can try to tackle the job yourself, although stump grinders are quite heavy and can be difficult to use at times. So how do you get rid of a tree stump then? What is the best way? Well, the answer is in the original suggestion of letting it rot away, but doing so quickly.

How To Get Rid Of A Tree Stump Fast?

The fastest way to remove a tree stump, with and without using a grinder, is the chemical method. By applying chemicals to holes drilled into the stump, you speed up the natural decay process and the remaining tree fibers and roots will break down much more quickly. It is considered one of the best ways to remove a tree stump from your yard. Here is how to use this method by following these steps.

DIY Steps To Rotting A Tree Stump From A Leading Arborist:

Begin on a dry day or after a number of dry days if possible. This way the tree stump will be looking for liquid and nutrients and will soak up the chemicals faster.

If you are capable, use a chainsaw to cut the remaining part of the tree as close to the ground as possible. By doing this the chemicals will have less material to eat through. Chainsaws can be dangerous though, so make sure you always use caution, wear steel-toed boots and eye protection.

Once the tree stump is as close to the ground as you can comfortably get it to go, drill a number of holes into the top of the stump and along the sides in a downward direction. The bigger the drill bit the better, and each of the holes should be a few inches deep.

After drilling the holes into the stump in different places, you will apply the chemicals that will break down the remaining wood. Utah does have strict legal restrictions about the kind of chemicals you can purchase for this sort of project. Ideally, you would want a commercial fertilizer that is high in nitrogen, since it will give you the fastest results, but cow manure is also effective. Another more natural alternative is Epsom salt. It is also a cost-effective solution as a 19lbs page starts at $10. It has similar dissolving properties to nitrogen but is a more organic approach. When you have chosen the chemical you will use, pack the holes with as much of it as you can.

Then soak the ground around the stump and wet the top and sides of the stump. After the stump is wet, cover it with a plastic tarp to trap the moisture around the stump. Moisture is ultimately what will help the chemicals break down the wood particles faster.
The next step is to apply mulch over the top of the plastic tarp. Organic mulch, like hay or tree bark, is best for this task as it will retain more moisture and help to keep the tarp in place.

You can use rocks and stones to weigh down the tarp further to help keep it in place, although this step is considered optional.
Once you have completed all of these steps, you are officially rotting a tree stump. This process is a speeding up of nature, and we all know that nature can take its time, so you should expect that it will take some time to work. How can you speed up the stump rot process even more? You can repeat the rotting steps periodically if you notice the mulch has grown dry.

How Much Does It Cost To Remove A Stump?

The overall cost for a stump removal is largely dependent on the method you choose to use. If you chose to do it yourself, it would be the cost of materials needed. Whereas, if you live in the nearby Utah area, with easy access to the stump, the average cost is about $6 per inch in diameter with $150-$200 minimum charge.

Looking To Remove a Tree Stump Quickly?

Ultimately, the quickest way to remove your tree stump and return your yard to a flat surface is the method of stump grinding. Although our grinding services are limited, if you are in need of a tree removal service in the Utah, area, or if you are looking to get some stumps removed don’t hesitate to contact the tree experts.

If you’re not a current or past tree client and have a stump you’d like removed, read more about stump rot and how to safely remove the tree stump yourself.

When your stump is ground, you can expect that there will be no masses of the stump left underground. The stump grindings, which are the wood shavings from the stump mixed with dirt, are left behind. You can use these grindings as mulch around your yard. Please remove the grindings prior to replanting any plants or trees in that area.

Stump Grinding FAQs

What is the average cost for stump grinding?

If you live in the nearby Utah Metro area with easy access to the stump, stump grinding cost averages about $6 per inch in diameter with a $150-$200 minimum. Anything that makes the stump harder to access and remove such as a fence or retaining wall or anything breakable such as a flagstone patio would increase the price from there. Also removing the stump grindings is almost always an additional charge.

Is It better to grind a stump or remove it?

There are many ways how to get rid of tree stumps, and there are advantages and disadvantages for either removing a stump or grinding it. For removing a stump the advantage is there is no stump grinding left behind. The disadvantages are that removing all but the smallest stumps usually requires large equipment such as a loader or excavator. In addition, it is usually pretty hard to find a place to dispose of them. For grinding a stump the advantages are that it can be done to almost any stump in any location or a reasonable fee and the disadvantages are that the grinding as usually left behind for the property owner to deal with.

Can you grind down a tree stump with a chainsaw?

There are stump grinders that attach to a chainsaws powerhead, but grinding a stump with a regular chainsaw would be exceptionally difficult as the chain would dull every time it hit even a small amount of dirt. It also sounds very dangerous.

Can I use ground up tree stump as mulch?

Yes, a ground-up tree stump makes an excellent mulch product.

How much does it cost to rent a stump grinder from Home Depot?
In the Utah Metro area $299 per day and $209 for 4 hours as of 3/20/19 to rent a grinder for stump removal in Utah, OR.

Does stump grinding kill roots?

No, in fact, the roots are sometimes spurred to grow more from the shock of having the tree removed and stump ground out.

Does tree removal include the stump?

The answer is almost always no. The removal of the stump in the ground is for an additional fee. Tree removal bids are very specific so any extra services such as stump grinding, wood removal, or tree removal permits are not included unless expressly stated.

Will tree stumps attract termites?

Yes, but not all termites will damage your home. It will take an exterminator to determine which kind you have should your stump become infested.

Can a tree grow back from a stump?

Depending on the type of tree they can grow back but this would not be a tree that you would want to keep as its structure would be compromised and thus it would be likely to fail and damage your property.

Contact the tree experts about stump removal in Utah

If you live in the Utah area and are looking to have a tree removed and are also interested in stump removal and grinding contact our nearby team of Utah stump grinding service professionals.

[geocentric_weather id=”1bcf073d-68b1-47b8-ba42-3e37b4e71f25″]

[geocentric_about id=”1bcf073d-68b1-47b8-ba42-3e37b4e71f25″]

[geocentric_neighborhoods id=”1bcf073d-68b1-47b8-ba42-3e37b4e71f25″]

[geocentric_thingstodo id=”1bcf073d-68b1-47b8-ba42-3e37b4e71f25″]

[geocentric_busstops id=”1bcf073d-68b1-47b8-ba42-3e37b4e71f25″]

[geocentric_mapembed id=”1bcf073d-68b1-47b8-ba42-3e37b4e71f25″]

[geocentric_drivingdirections id=”1bcf073d-68b1-47b8-ba42-3e37b4e71f25″]

[geocentric_reviews id=”1bcf073d-68b1-47b8-ba42-3e37b4e71f25″]

Tree Cutting Service Near Me

Tree Cutting Service Near Me

A feller buncher is a type of harvester used in logging. It is a motorized vehicle with an attachment that can rapidly gather and cut a tree before felling it.

Feller is a traditional name for someone who cuts down trees, and bunching is the skidding and assembly of two or more trees. A feller buncher performs both of these harvesting functions and consists of a standard heavy equipment base with a tree-grabbing device furnished with a chain-saw, circular saw or a shear—a pinching device designed to cut small trees off at the base. The machine then places the cut tree on a stack suitable for a skidder, forwarder, or yarder for transport to further processing such as delimbing, bucking, loading, or chipping.

Some wheeled feller bunchers lack an articulated arm, and must drive close to a tree to grasp it.

In cut-to-length logging a harvester performs the tasks of a feller buncher and additionally does delimbing and bucking.

Components and Felling attachment

Feller buncher is either tracked or wheeled and has self-levelling cabin and matches with different felling heads. For steep terrain, tracked feller buncher is being used because it provides high level of traction to the steep slope and also has high level of stability. For flat terrain, wheeled feller buncher is more efficient compared to tracked feller buncher. It is common that levelling cabins are matched with both wheeled and tracked feller buncher for steep terrain as it provides operator comfort and helps keeping the standard of tree felling production. The size and type of trees determine which type of felling heads being used.

Types of felling heads

Disc Saw Head – It can provide a high speed of cutting when the head is pushed against the tree. Then, the clamp arms will hold the tree when the tree is almost completed cutting. It is able to cut and gather multiple trees in the felling head. The disc saw head with good ground speed could provide high production which allows it to keep more than one skidders working continuously.
Shear Blade Head – It is placed against the tree and the clamp arms will hold the tree firmly. Then, the blade will activate and start cutting the tree. Same as disc saw head, it can hold multiple trees before they are placed on the ground.
Chain Saw Head – The floppy head provides minimal control to place the trees on the ground. It might not suit to collect the cut trees or gather the cut stems in the felling head.

Productivity

Comparing other harvesting systems such as chainsaw and harvester, feller buncher has the relatively high productivity among them. The weekly production of the feller buncher was 627 cubic meters of usable logs, while the chainsaw system and harvester system could produce 163 cubic meters and 239 cubic meters respectively. There are several factors affecting the level of productivity of the feller buncher. They include characteristics of stand, terrain conditions, operation location, and the performance of the operator. Many studies indicated that the trees size and the gradient of the slope are the major factors impacting the overall productivity. There was a research suggested that productivity has a significant positive relationship with the tree size which means the larger stem size, larger tree height or larger diameter at breast height (DBH) results in a high productivity of the feller buncher. Terrain conditions such as ground slope and terrain roughness have a significant negative relationship to the productivity of feller buncher which means the steeper of the land or rough terrain condition can bring negative effect to the productivity. One of the studies had found that feller buncher might reduce its productivity when performing operation on a very uneven surface with slopes of more than 20%. However, larger tree size does not necessarily lead to high productivity. The same study compared the operation time when performing clear-cut of the stands with two different average DBH, 24.6 cm and 34.3 cm respectively. Result showed that the productivity when operating the second stand decreased by 32.3% because the time consumption was doubled when larger stands required two-stage of cutting operation.

Cost-effectiveness

The purchase cost of a feller buncher is around $180,000 and its fuel consumption and lubricant consumption is high among other mechanical harvesting equipment. The feller buncher also has the highest hourly cost which is around $99.5 when comparing other equipment such as a harvesters and grapple skidders. Although the total cost of feller buncher is high in overall, the unit production price is the lowest which explains why feller buncher is considered the most cost-effective harvesting equipment. The average unit cost of the feller buncher is $12.1/m3 while the unit cost of the harvesters is $16.5/m3. The unit cost of the feller buncher is primary affected by the tree size and the tree volume. The unit felling cost is lower when the tree size increased. For example, tree with 5 inches at DBH has the unit cost of $70 while tree with 15 inches at DBH has the unit cost of $12. As the cost of feller buncher is high, only large tree volume can produce more profit to cover the high average cost. In terms of stump height, lower stump height can maximise the use of natural resources and prevent wood waste. Mechanical felling such as using feller buncher can prevent 30% of value loss caused by the high stumps.

Maintenance

Feller buncher requires daily maintenance before operation and some components only require periodic maintenance. It could ensure the safety of operators and all the workers around the operation. If damaged or faulty machine is operated, it could result in further damage to the machine which can be more expensive to repair.

Daily or Every 8 hours

Modern style Tigercat feller buncher. Commonly referred to as a tree cutter.

Lubrication

The felling head is considered one of the hardest part of the feller buncher and it is necessary to apply lubricant to every joint for daily maintenance. It is suggested to apply lubricant to saw head clamps, wrist attachment and driveshaft bearings during every maintenance. The use of grease should meet the extreme pressure performance standard and contains 3% of molybdenum disulphide (MoS2). MoS2 can prevent the wear takes place where the metal to metal contact exists.

Fuel

It is also important to check if there is enough fuel for the operation. Feller bunchers use diesel fuel to generate power. In most of the cases, the fuel is preferably to have cetane number greater than 50 (minimum 40). This is suitable when undergo operation for temperature below -20 °C (-4 °F) or elevations more than 1500m (5000 Ft.). The Cloud Point of the fuel is preferably at least 5 °C (9 °F) lower than the expected low temperature. It is also suggested that the sulphur content of the fuel should not be more than 0.5% as it could reduce 50% of the service interval for the engine oil and filter.

Older style felling head that uses a bar and chain to cut trees instead of the more modern saw disk.

Engine coolant

Operators have the responsibility to check the engine coolant level of the feller buncher before starting the engine. The coolant prevents cylinder linear erosion and pitting, and provides protection during extremely low temperature for up to -37 °C (-34 °F). It is recommended to use coolants for heavy-duty engines which are relatively low silicate ethylene glycol base. There are two forms of coolants: pre-diluted or concentrate. Water is required to dilute the concentrated coolant with an approximate ratio of 50:50. The use of supplemental coolant addictive might be also required in the concentrated coolant in order to provide protection against corrosion. Distilled, deionised, or demineralised water is suggested for mixing the concentrated coolant because when some water compositions mix with other substances could form a precipitate, causing damage or blockage in the engine.

Risk management approach

During maintenance, there are common working hazards related to two main areas: working environment and exhaust system. When working on the exhaust system, be aware of the hot components around the engine. Workers could wear personal protective equipment such as safety spectacles, heat-proof gloves and safety boots. When feller buncher is elevated for service or maintenance, falls from height might happen. Related injuries could be avoided by ensuring dryness of all the walking surface, wiping any oils or other liquid substances on the floor. Also, ensure the feller buncher is parked on a level and stable ground during maintenance. When getting in and out of the machinery, workers are suggested to use three point of contact with two hands holding the handrails and one foot on a step. It is also important to provide sufficient lighting for all the working sites at all time of service.

Safety

Logging is considered one of the most dangerous occupations. This is because many loggers are injured by the falling objects which are large in size and heavy. “Struck by object” is the most common injuries that reported in the logging industry due to the manual use of equipment during the logging procedures. There is evidence that using mechanized harvesting equipment could reduce the rate of “struck by” injuries. One study indicates that total injury claims could be reduced by 14.2%, while the “struck by” injuries could be reduced by 8.2%, when comparing the changes before and after the use of feller buncher. The significant decline in the number of “struck by” injuries after using the feller buncher in the logging companies supported the statement that using mechanized harvesting equipment could lessen overall injuries. The evidence also found that the rate of injuries in the logging companies without using feller bunchers had increased slightly throughout a period of time, increasing from 14.5% to 17.5%, in five years. In terms of trees fatality, areas with lower levels of mechanization in harvesting resulted in higher rate of trees fatality. For instance, in Eastern areas of the United States, research which compared the conventional and mechanized logging operations, indicated the number of injuries, when using the conventional approach, is three times greater than that of using the mechanized equipment such as a feller buncher. However, mechanized related injury could be raised accordingly, especially when performing machine maintenance or repair. These kinds of injuries could be serious and also costly.

[geocentric_weather id=”939ac304-6c09-455f-a764-da066e6f34c4″]

[geocentric_about id=”939ac304-6c09-455f-a764-da066e6f34c4″]

[geocentric_neighborhoods id=”939ac304-6c09-455f-a764-da066e6f34c4″]

[geocentric_thingstodo id=”939ac304-6c09-455f-a764-da066e6f34c4″]

[geocentric_busstops id=”939ac304-6c09-455f-a764-da066e6f34c4″]

[geocentric_mapembed id=”939ac304-6c09-455f-a764-da066e6f34c4″]

[geocentric_drivingdirections id=”939ac304-6c09-455f-a764-da066e6f34c4″]

[geocentric_reviews id=”939ac304-6c09-455f-a764-da066e6f34c4″]

Stump Grinding Near Me

Stump Grinding Near Me

WHAT IS STUMP GRINDING?

When providing a proposal for a tree removal, an arborists also evaluate the site for stump grinding. While having the stump ground is not always necessary, many people prefer to deal with the stump at the same time as having the tree removed. Stump grinding allows the property owner to use the area where the tree once stood for laying sod or planting a flower bed. The stump grinder also produces mulch that has many uses around the yard. Here are answers to some common questions we get about stump grinding.

HOW DEEP CAN THE STUMP GRINDER GO?

They generally grind four to six inches below grade (ground level). If deeper grinding is needed, it can be requested, although the price of stump grinding may increase. The depth to which a stump can be ground is subject to some limitations, however. The stump-grinding blade has a diameter of about 10 inches, and can only be maneuvered up and down within a specific range.
A tree that grew in shallow soil, such as over the limestone bedrock prevalent in the Dallas area, may not have six inches of grindable depth.

Other material near or around the tree may limit how deep the grinder can go. While the stump grinder is powerful, it is only designed to handle plant material, wood, and dirt. Take note of:

Fencing, concrete, brick, or rock around a stump (such as a tree ring)

Nearby trees that may have roots under the tree stump

Swimming pools, walkways, and patios that may prevent the grinder from reaching all of the root material

Lawn irrigation, sprinkler systems, tree lighting wiring, and buried hoses

We generally do not grind deep enough to risk interfering with properly-installed utility lines or buried cables, but unforeseen obstacles can be encountered that necessitate a shallower grind.

What exactly lies beneath the roots of a tree or the surrounding soil may be a mystery, even to the homeowner. While we are very careful when grinding a stump, we will not take responsible for damage to irrigation lines or other items located below ground that we are not aware of. It is important to inform your arborist of any sprinkler systems or other objects that might be in the area to be ground before the work begins.

WHAT IS LEFT AFTER A STUMP IS GROUND?

As the blade grinds the stump and surface roots, it produces a mulch made up of tree material and dirt. The mulch produced by stump grinding can take up a much greater volume than the original stump. (It can be helpful to think of the difference between a block of cheese and that same cheese after it is grated.)

Mulch from stump grinding is valuable organic material that decomposes more quickly than many other kinds of mulch, as there are generally smaller wood particles present, and more soil to help it break down. It is our standard practice to push the mulch back into the area that has been ground (“backfilling”). Even so, there is usually a large pile of mulch left above ground, often much more than the tree owner expected. Because of its composition, the mulch does settle fairly quickly, but many people prefer to use the mulch around their yards, rather than leaving it where the stump once was.

Stump grinder mulch can be used for composting or applied in flower beds. (Depending on exact composition of the mulch, it may not perform in the same way as typical hardwood mulch, and may need to be replaced sooner.) After some time, when the mulch has settled, it can be packed into the ground-out area, making the area ready to be prepped for laying sod or for planting a flower bed or other small plants. If requested, we can provide mulch bagging and/or bagged mulch haul-off as an additional service after stump grinding, but our standard practice is to leave all grinder mulch on-site.

WILL THE TREE COME BACK AFTER A STUMP IS GROUND?

Even with stump grinding, some species of tree can still send up shoots and new growth from the roots left below ground. Crape myrtles, chinaberry trees, hackberries, and Bradford pears are some common species in the area that can be very persistent in growing back. The sprouts that return after stump grinding can be trimmed or mown down and will eventually stop coming back, as the remaining roots use up their energy reserves. Commercially-available woody stem killer can be used to accelerate the dieback of the roots. White vinegar can also be used as an organic alternative to commercial root killer.

CAN I REPLANT AFTER A STUMP IS GROUND?

We are often contacted about removing a tree that the owner would like to replace. We do not recommend trying to re-plant trees in the same area where a tree was removed and the stump ground. Even with a deep grind, an extensive root system remains underground. The old root system can interfere with the new tree’s attempts to become established. Furthermore, if the old tree had a disease, that disease may still be present in the remaining root tissue, and can be transmitted to the new tree. When replanting is desired, we can discuss finding a location that is far enough from the removed tree to lessen the likelihood of interference from the old root system. If homeowners’ association or municipal restrictions require a tree to be replaced in a certain location, excavation or hand digging may be the only options.

CAN EVERY STUMP BE GROUND?

In the case of a tree becoming uprooted (because of storm damage or root rot, for example), the stump cannot be dealt with as easily. If there is a large amount of root material above ground, the stump grinder may be physically unable to reach it. Depending on the type of tree and how it grew, it may pull up a great deal of dirt, turf grass, and other underground material when it falls. What is left after grinding an uprooted stump may be more dirt than tree matter, and may not be suitable for use as mulch.

Weather is also a factor that can determine how and when stump grinding can be performed. A long period of rain can cause the soil to become waterlogged. Operating a stump grinder in heavy, wet soil can not only make a bigger mess than usual, but can damage the surrounding area due to the weight of the machine. It may be necessary to wait until the area dries out before attempting even a “standard” stump grind.

If a customer has a special circumstance, like an uprooted tree, or there are multiple stumps in one area to be ground, we always send an arborist to assess the situation before providing a quote or scheduling the stump grinder.

HOW MUCH DOES STUMP GRINDING COST?

The cost of stump grinding is dependent upon three main factors: the size of the stump, the location of the stump, and how deep the grinder needs to go. While we generally provide a stump grinding price when we give a quote for tree removal, we are also happy to evaluate any other stumps you may want to have ground.

HOW DO I MEASURE A STUMP?

The base cost for stump grinding is determined by the diameter of the stump in inches, including any above-ground roots. This measurement can be taken before or after a tree is removed. To get the right measurement, it is important to go “from dirt to dirt.” This means measuring from the stump edge or root point (where it touches the dirt) farthest from the trunk to the opposite edge or root point. It is also important to measure from different directions and to take an average measurement, as this most accurately reflects the area to be ground. The “dirt-to-dirt” measurement can be quite a bit larger than the diameter of the tree trunk, and we do see situations where the stump grinding is more costly than removing the above-ground tree.
This is a 75-inch stump, measured “dirt to dirt” at the yellow line. Measuring on the trunk is inaccurate: if this tree were measured at the red line, the result would only be 37 inches, which is not the actual area to be ground. Even after a tree is cut down, properly measuring a stump can be tricky when there is a root flare and surrounding vegetation.

CAN THE STUMP GRINDER REACH MY STUMP?

Our standard stump grinder is a machine that is seven feet long and three feet wide. At the front is a rounded blade (similar to the tip of a chainsaw) that chips away wood as it moves across the stump. The stump grinder is designed to fit through standard gates, but some older or narrow gates may not be able to accommodate it. The weight of the machine may also prevent it from reaching certain areas without damaging walkways or ground cover. While the grinding blade has some maneuverability, clearance of at least seven feet on one side of the stump is required to allow the grinder to access the area to be ground. In smaller areas with less clearance, it is possible to use our smaller stump grinder, but this can increase the time and cost of the procedure.

CAN I JUST LEAVE THE STUMP?

It is not necessary to grind or otherwise remove a stump after a tree is taken down. We have customers who request a tree not be cut all the way to ground level, and use the remaining stump as a plant stand, table base, or just a yard feature. Even if the stump is cut close to the ground, it can last several years. Preservative coatings can also be applied to prolong the life of a standing stump.

Some homeowners prefer to let a stump decompose naturally over time. Old stumps can become habitats for fungi, insects, and other creatures. As the stump breaks down, it can become rich organic material that can be added to compost or used in planting. If a stump is left unground, however, it can continue to send out new growth for years after the tree has been removed. Drilling holes in the stump and filling with Epsom salt or using commercial stump killer can accelerate stump dieback, but those chemicals can be toxic to surrounding plant life. Treating the stump with chemicals can also make the area hazardous to people and pets.

[geocentric_weather id=”7a10afb3-616b-40b1-b3ad-9668dcee5aee”]

[geocentric_about id=”7a10afb3-616b-40b1-b3ad-9668dcee5aee”]

[geocentric_neighborhoods id=”7a10afb3-616b-40b1-b3ad-9668dcee5aee”]

[geocentric_thingstodo id=”7a10afb3-616b-40b1-b3ad-9668dcee5aee”]

[geocentric_busstops id=”7a10afb3-616b-40b1-b3ad-9668dcee5aee”]

[geocentric_mapembed id=”7a10afb3-616b-40b1-b3ad-9668dcee5aee”]

[geocentric_drivingdirections id=”7a10afb3-616b-40b1-b3ad-9668dcee5aee”]

[geocentric_reviews id=”7a10afb3-616b-40b1-b3ad-9668dcee5aee”]